WeldBilt 72 in. Beam 2012 boat specs
WeldBilt
WeldBilt 72 in. Beam 2012
2012
View full specs →
VS
WeldBilt 77 in. Beam 2010 boat specs
WeldBilt
WeldBilt 77 in. Beam 2010
2010
View full specs →

WeldBilt 72 in. Beam 2012 vs WeldBilt 77 in. Beam 2010 — A Close Look at Two Flats

When two boats share the same hull type — in this case both the WeldBilt 72 in. Beam 2012 and the WeldBilt 77 in. Beam 2010 are flat designs with aluminum construction — the buying decision usually comes down to a handful of practical questions: how many people are you putting on the water, how far do you trailer, and what does your tow vehicle weigh?

On paper these two are close siblings in the size department — WeldBilt 72 in. Beam 2012 at 15,0 ft versus WeldBilt 77 in. Beam 2010 at 16,0 ft. At 34 lbs and 41 lbs respectively, both sit in a similar weight class — either should pair comfortably with most mid-size SUVs and half-ton trucks, though always confirm your specific tow rating with the motor added.

Bottom line: The WeldBilt 72 in. Beam 2012 and WeldBilt 77 in. Beam 2010 are closely matched on the specs that matter most. Test-ride both on the water you actually use, check current dealer pricing, and factor in long-term service access before you sign.
General Boat Info
MakeWeldBilt
MakeWeldBilt
Model72 in. Beam
Model77 in. Beam
Model Year2012
Model Year201
Measurements / Dimensions
Beam72 in
Beam77 in
Beam - Meters1.83
Beam - Meters1.96
Beam - Inches72
Beam - Inches77
Weight - Detail340 lbs
Weight - Detail410 lbs
Weight - kg154.22
Weight - kg185.97
Weight - lbs.34
Weight - lbs.41
Height - Detail20 in
Height - Detail24 in
Height - Meters0.51
Height - Meters0.61
Height - Inches2
Height - Inches24
Length - Feet15
Length - Feet16
Body / Hull
Hull materialAluminum
Hull materialAluminum
Hull thickness0.80 or 0.100 in
Hull thickness0.100 in
Hull typeFlat
Hull typeFlat
Engine and Drivetrain
Fuel typeGas
Fuel typeGas
Drive typeOutboard
Drive typeOutboard

WeldBilt 72 in. Beam 2012 vs WeldBilt 77 in. Beam 2010 — Common Questions

Which is the larger boat — the WeldBilt 72 in. Beam 2012 or the WeldBilt 77 in. Beam 2010?
The WeldBilt 77 in. Beam 2010 is the longer of the two at 16,0 feet overall. The WeldBilt 72 in. Beam 2012 comes in at 15,0 feet, making it roughly 1,0 ft shorter — a meaningful difference in deck room and overall on-water presence.
Which is easier to trailer — the WeldBilt 72 in. Beam 2012 or the WeldBilt 77 in. Beam 2010?
For trailering, the WeldBilt 72 in. Beam 2012 has the edge at 34 lbs dry weight versus 41 lbs for the WeldBilt 77 in. Beam 2010. Add a motor (typically 300–500 lbs for an outboard in this class), gear, and a partial fuel load and the difference grows. Lighter is friendlier on smaller tow vehicles and on fuel economy while hauling.
Which boat is wider, and does it affect trailering?
The WeldBilt 77 in. Beam 2010 measures 77" wide, compared to 72" for the WeldBilt 72 in. Beam 2012. The US standard-width towing limit is 8’6" (102") in most states — anything over that may need a wide-load permit. Confirm your specific route requirements with each state's DOT.
Are the WeldBilt 72 in. Beam 2012 and WeldBilt 77 in. Beam 2010 from the same manufacturer?
Yes — both the WeldBilt 72 in. Beam 2012 and the WeldBilt 77 in. Beam 2010 are built by WeldBilt. That means shared dealer networks, common parts availability, and consistent build quality across the line. The choice between them is essentially a question of how much boat you need, not which brand you trust.