WeldBilt 55 in. Beam 2010 boat specs
WeldBilt
WeldBilt 55 in. Beam 2010
2010
View full specs →
VS
WeldBilt 60 in. Beam 2012 boat specs
WeldBilt
WeldBilt 60 in. Beam 2012
2012
View full specs →

WeldBilt 55 in. Beam 2010 vs WeldBilt 60 in. Beam 2012: A Close Look at Two Flat-Bottom Boats

Both the WeldBilt 55 in. Beam 2010 and the WeldBilt 60 in. Beam 2012 are flat-bottom designs, both built in aluminium, so the buying decision usually comes down to a handful of practical questions: how many people are you putting on the water, how far do you trailer, and what does your tow vehicle weigh?

On paper these two are close siblings in the size department - WeldBilt 55 in. Beam 2010 at 10,0 ft versus WeldBilt 60 in. Beam 2012 at 12,0 ft. At 175 lbs and 235 lbs respectively, both sit in a similar weight class - either should pair comfortably with most mid-size SUVs and half-ton trucks, though always confirm your specific tow rating with the motor added.

Bottom line: The WeldBilt 55 in. Beam 2010 and WeldBilt 60 in. Beam 2012 are closely matched on the specs that matter most. Test-ride both on the water you actually use, check current dealer pricing, and factor in long-term service access before you sign.
General Boat Info
MakeWeldBilt
MakeWeldBilt
Model55 in. Beam
Model60 in. Beam
Model Year2010
Model Year2012
Measurements / Dimensions
Beam55 in.
Beam60 in.
Beam - Meters1.4
Beam - Meters1.52
Beam - Inches55
Beam - Inches60
Weight - Detail175 lbs.
Weight - Detail235 lbs.
Weight - kg79.38
Weight - kg106.59
Weight - lbs.175
Weight - lbs.235
Height - Detail20 in.
Height - Detail20 in.
Height - Meters0.51
Height - Meters0.51
Height - Inches20
Height - Inches20
Length - Feet10
Length - Feet12
Body / Hull
Hull materialAluminum
Hull materialAluminum
Hull thickness0.80 in.
Hull thickness0.80 in.
Hull typeFlat
Hull typeFlat
Engine and Drivetrain
Fuel typeGas
Fuel typeGas
Drive typeOutboard
Drive typeOutboard

WeldBilt 55 in. Beam 2010 vs WeldBilt 60 in. Beam 2012 - Common Questions

Which is the larger boat - the WeldBilt 55 in. Beam 2010 or the WeldBilt 60 in. Beam 2012?
The WeldBilt 60 in. Beam 2012 is the longer of the two at 12,0 feet overall. The WeldBilt 55 in. Beam 2010 comes in at 10,0 feet, making it roughly 2,0 ft shorter - a meaningful difference in deck room and overall on-water presence.
Which is easier to trailer - the WeldBilt 55 in. Beam 2010 or the WeldBilt 60 in. Beam 2012?
For trailering, the WeldBilt 55 in. Beam 2010 has the edge at 175 lbs dry weight versus 235 lbs for the WeldBilt 60 in. Beam 2012. Add a motor (typically 300–500 lbs for an outboard in this class), gear, and a partial fuel load and the difference grows. Lighter is friendlier on smaller tow vehicles and on fuel economy while hauling.
Which boat is wider, and does it affect trailering?
The WeldBilt 60 in. Beam 2012 measures 60" wide, compared to 55" for the WeldBilt 55 in. Beam 2010. The US standard-width towing limit is 8’6" (102") in most states - anything over that may need a wide-load permit. Confirm your specific route requirements with each state's DOT.
Are the WeldBilt 55 in. Beam 2010 and WeldBilt 60 in. Beam 2012 from the same manufacturer?
Yes - both the WeldBilt 55 in. Beam 2010 and the WeldBilt 60 in. Beam 2012 are built by WeldBilt. That means shared dealer networks, common parts availability, and consistent build quality across the line. The choice between them is essentially a question of how much boat you need, not which brand you trust.