WeldBilt 55 in. Beam 2010 boat specs
WeldBilt
WeldBilt 55 in. Beam 2010
2010
View full specs →
VS
WeldBilt 55 in. Beam 2011 boat specs
WeldBilt
WeldBilt 55 in. Beam 2011
2011
View full specs →

WeldBilt 55 in. Beam 2010 vs WeldBilt 55 in. Beam 2011 — A Close Look at Two Flats

When two boats share the same hull type — in this case both the WeldBilt 55 in. Beam 2010 and the WeldBilt 55 in. Beam 2011 are flat designs with aluminum construction — the buying decision usually comes down to a handful of practical questions: how many people are you putting on the water, how far do you trailer, and what does your tow vehicle weigh?

On paper these two are close siblings in the size department — WeldBilt 55 in. Beam 2010 at 1,0 ft versus WeldBilt 55 in. Beam 2011 at 1,0 ft. At 175 lbs and 175 lbs respectively, both sit in a similar weight class — either should pair comfortably with most mid-size SUVs and half-ton trucks, though always confirm your specific tow rating with the motor added.

Bottom line: The WeldBilt 55 in. Beam 2010 and WeldBilt 55 in. Beam 2011 are closely matched on the specs that matter most. Test-ride both on the water you actually use, check current dealer pricing, and factor in long-term service access before you sign.
General Boat Info
MakeWeldBilt
MakeWeldBilt
Model55 in. Beam
Model55 in. Beam
Model Year201
Model Year2011
Measurements / Dimensions
Beam55 in
Beam55 in
Beam - Meters1.4
Beam - Meters1.4
Beam - Inches55
Beam - Inches55
Weight - Detail175 lbs
Weight - Detail175 lbs
Weight - kg79.38
Weight - kg79.38
Weight - lbs.175
Weight - lbs.175
Height - Detail20 in
Height - Detail20 in
Height - Meters0.51
Height - Meters0.51
Height - Inches2
Height - Inches2
Length - Feet1
Length - Feet1
Body / Hull
Hull materialAluminum
Hull materialAluminum
Hull thickness0.80 in
Hull thickness0.80 in
Hull typeFlat
Hull typeFlat
Engine and Drivetrain
Fuel typeGas
Fuel typeGas
Drive typeOutboard
Drive typeOutboard

WeldBilt 55 in. Beam 2010 vs WeldBilt 55 in. Beam 2011 — Common Questions

Which is the larger boat — the WeldBilt 55 in. Beam 2010 or the WeldBilt 55 in. Beam 2011?
The WeldBilt 55 in. Beam 2011 is the longer of the two at 1,0 feet overall. The WeldBilt 55 in. Beam 2010 comes in at 1,0 feet, making it roughly 0,0 ft shorter — a meaningful difference in deck room and overall on-water presence.
Which is easier to trailer — the WeldBilt 55 in. Beam 2010 or the WeldBilt 55 in. Beam 2011?
For trailering, the WeldBilt 55 in. Beam 2011 has the edge at 175 lbs dry weight versus 175 lbs for the WeldBilt 55 in. Beam 2010. Add a motor (typically 300–500 lbs for an outboard in this class), gear, and a partial fuel load and the difference grows. Lighter is friendlier on smaller tow vehicles and on fuel economy while hauling.
Do these boats require an oversize trailer permit to tow on US highways?
Both the WeldBilt 55 in. Beam 2010 and WeldBilt 55 in. Beam 2011 share an 55 in beam — meaning both sit right at the 8’6" threshold that most US states use for standard-width loads. In most states you can tow at that width without a special permit, but regulations vary. Always check the rules for your state and any states you'll be passing through before your first long haul.
Are the WeldBilt 55 in. Beam 2010 and WeldBilt 55 in. Beam 2011 from the same manufacturer?
Yes — both the WeldBilt 55 in. Beam 2010 and the WeldBilt 55 in. Beam 2011 are built by WeldBilt. That means shared dealer networks, common parts availability, and consistent build quality across the line. The choice between them is essentially a question of how much boat you need, not which brand you trust.