Alumacraft All Weld MV 1650 2011 boat specs
Alumacraft
Alumacraft All Weld MV 1650 2011
2011
View full specs →
VS
Alumacraft Lunker 165 CS 2008 boat specs
Alumacraft
Alumacraft Lunker 165 CS 2008
2008
View full specs →

Alumacraft All Weld MV 1650 2011 vs Alumacraft Lunker 165 CS 2008: Same Brand, Different Boat

The Alumacraft All Weld MV 1650 2011 is a modified-V design and the Alumacraft Lunker 165 CS 2008 is a deep-V design, so you're likely deciding between two noticeably different on-water experiences. Hull type shapes everything from ride quality and fuel burn to dock handling and resale trajectory.

On paper these two are close siblings in the size department - Alumacraft All Weld MV 1650 2011 at 16,0 ft versus Alumacraft Lunker 165 CS 2008 at 16,0 ft. Weight tells a clearer story for trailering families: the Alumacraft Lunker 165 CS 2008 tips the scales at 700 lbs - 215 lbs less than the Alumacraft All Weld MV 1650 2011 at 485 lbs. That difference is meaningful if you're working within a half-ton or three-quarter-ton truck's tow rating, especially once you factor in a motor, gear, and fuel.

Both boats share a closely matched power ceiling - 40 hp for the Alumacraft All Weld MV 1650 2011 and 50 hp for the Alumacraft Lunker 165 CS 2008. Real-world performance will come down more to which motor is actually bolted on, its load at the time, and whether it's a 4-stroke or 2-stroke setup.

Both boats are rated for 5 passengers - a good fit for a family of four or five plus guests. Comfort at capacity is another matter; the longer hull typically means more seat options and better weight distribution.

At this size, power-to-weight ratio matters more than outright horsepower. The Alumacraft All Weld MV 1650 2011 comes in at 12 lbs per hp versus 14 lbs per hp for the Alumacraft Lunker 165 CS 2008. The lower the ratio the more explosive the acceleration - meaningful on a short RIB where bursts of speed, quick planing, and agility in surf or tight waterways define the experience.

Bottom line: The Alumacraft All Weld MV 1650 2011 and Alumacraft Lunker 165 CS 2008 are closely matched on the specs that matter most. Test-ride both on the water you actually use, check current dealer pricing, and factor in long-term service access before you sign.
General Boat Info
MakeAlumacraft
MakeAlumacraft
ModelAll Weld MV 1650
ModelLunker 165 CS
Model Year2011
Model Year2008
Measurements / Dimensions
Beam74 in.
Beam76 in. (1.92 m)
Beam - Meters1.88
Beam - Meters1.93
Beam - Inches74
Beam - Inches76
Weight - Detail485 lbs.
Weight - Detail700 lbs. (317 kg)
Weight - kg219.99
Weight - kg317.51
Weight - lbs.485
Weight - lbs.700
Height - Detail22 in.
Height - Detailnot available
Height - Meters0.56
Height - Metersnot available
Height - Inches22
Height - Inchesnot available
Height [transom]21 in.
Height [transom]20 in. (0.51 m)
Length - Feet16
Length - Feet16
Length overall - Detail16 ft. 0 in.
Length overall - Detail16 ft. 6 in. (5 m)
Length overall - Meters4.88
Length overall - Meters5.03
Length overall - Inches192
Length overall - Inches198
Depth - Detailnot available
Depth - DetailMaximum: 35 in. (0.88 m) To Floor: 22 in. (0.54 m)
Depth - Centimetersnot available
Depth - Centimeters88.9
Depth - Inchesnot available
Depth - Inches35
Width [transom] - Detailnot available
Width [transom] - Detail73 in. (1.85 m)
Length - Metersnot available
Length - Meters5
Length - Inchesnot available
Length - Inches6
Body / Hull
Hull materialAluminum
Hull materialAluminum
Hull thickness0.102 in.
Hull thicknessBottom: 0.080 in. (2 mm)
Hull typeModified Vee
Hull typeDeep Vee
Engine and Drivetrain
Fuel typeGas
Fuel typeGas
Drive typeOutboard
Drive typeOutboard
Engine max40 hp
Engine max50 hp (37 kW)
Operational Info
Maximum capacity1,100 lbs.
Maximum capacity1,235 lbs. (560kg)
Maximum people5
Maximum people5

Alumacraft All Weld MV 1650 2011 vs Alumacraft Lunker 165 CS 2008 - Common Questions

Which is the larger boat - the Alumacraft All Weld MV 1650 2011 or the Alumacraft Lunker 165 CS 2008?
The Alumacraft Lunker 165 CS 2008 is the longer of the two at 16,0 feet overall. The Alumacraft All Weld MV 1650 2011 comes in at 16,0 feet, making it roughly 0,0 ft shorter - a meaningful difference in deck room and overall on-water presence.
Which is easier to trailer - the Alumacraft All Weld MV 1650 2011 or the Alumacraft Lunker 165 CS 2008?
For trailering, the Alumacraft All Weld MV 1650 2011 has the edge at 485 lbs dry weight versus 700 lbs for the Alumacraft Lunker 165 CS 2008. Add a motor (typically 300–500 lbs for an outboard in this class), gear, and a partial fuel load and the difference grows. Lighter is friendlier on smaller tow vehicles and on fuel economy while hauling.
Which boat can handle a bigger outboard?
The Alumacraft Lunker 165 CS 2008 is rated to a maximum of 50 hp, giving it the larger power ceiling. The Alumacraft All Weld MV 1650 2011 tops out at 40 hp. Keep in mind that maximum ratings are just that - matching the motor to the actual load and usage pattern usually matters more than chasing the ceiling.
How many people can each boat hold?
The Alumacraft All Weld MV 1650 2011 is Coast Guard rated for 5 passengers, while the Alumacraft Lunker 165 CS 2008 is certified for 5. Note that legal capacity and comfortable capacity aren't always the same thing - on a full day out, most experienced boaters aim for about 80% of the rated number to keep things comfortable.
Which boat has the better power-to-weight ratio?
The Alumacraft All Weld MV 1650 2011 has a better power-to-weight ratio at 12 lbs per hp compared to 14 lbs per hp for the Alumacraft Lunker 165 CS 2008. A lower number means quicker acceleration and faster time to plane - the number that actually matters most on short, sporty boats like these.
Which boat is wider, and does it affect trailering?
The Alumacraft Lunker 165 CS 2008 measures 76" wide, compared to 74" for the Alumacraft All Weld MV 1650 2011. The US standard-width towing limit is 8’6" (102") in most states - anything over that may need a wide-load permit. Confirm your specific route requirements with each state's DOT.
Are the Alumacraft All Weld MV 1650 2011 and Alumacraft Lunker 165 CS 2008 from the same manufacturer?
Yes - both the Alumacraft All Weld MV 1650 2011 and the Alumacraft Lunker 165 CS 2008 are built by Alumacraft. That means shared dealer networks, common parts availability, and consistent build quality across the line. The choice between them is essentially a question of how much boat you need, not which brand you trust.